Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 173)



dial_mode [string]: Selects “tone” dialing or “pulse” dialing. Defines whether the driver sends            

an ATDT<dial number> or ATDP<dial number>. Format: Either TONE or PULSE. Default:           

TONE.



dial_progress_mode [string]: Determines if dial and busy tones are detected. The driver           

implements this by sending the X# modem command depending upon this value. Format:            

Comma separated list of DETECT_BUSY_TONE and DETECT_DIAL_TONE. Default:       

DETECT_DIAL_TONE,DETECT_BUSY_TONE.



dsr_delta_reset_timeout_msecs [dword 0–65535]: How often to wait after DSR comes         

back on before resetting the modem. If a modem is turned off, this determines how long after it                 

comes back on before the driver resets it. When a modem is turned off, and thus, drops its DSR                  

modem status, the driver will immediately report that the modem is DEFECTIVE. When the             

modem is turned back on, the driver immediately notice that DSR is raised, however, the              

modem may need several seconds to wake up before any commands are sent to it. This feature                

isnotabletobeimplementedwhenusingTAPI.Default:10000.



dte_baud_rate [dword 2–115200]: Baud rate for CLASS1 to use to talk to the modem at all               

times, unless the 2400_baud_init setting is YES in which case the driver will only use the               

dte_baud_rate when the modem is in Class1 mode. There have been cases on slow machines              

where setting this to a baud rate like 38400 or 57600 reduces the likelihood of send underrun                

errors occurring. Setting this to lower than 19200 has the possibility that the UART won't be               

abletokeepupwiththemodemmodulationthroughputduetoextraDLEescaped

characters.Default:38400.



dtmf_detection_begin [string]: When the line_type is DTMF_PROMPT, this command is sent          

to the modem before answering. It should cause the modem to go off hook, emit a prompt tone                 

if possible and collect and report received DTMF digits. This has the same formate rules as the                

init_string, plus a /{ sequence is translated to a DLE (0x10) character and a /} sequence is                

translatedtoaETX(0x03)character.Format:Upto80characters.Default:#CLS=8A.



dtmf_detection_end [string]: This is what needs to be sent to the modem to get it out of the                 

state that the dtmf_detection_begin put it in. It is sent by the driver when either the 6 second                 

interdigit DTMF timeout occurs or the dtmf_terminate_digits is received. This has the same            

formatrulesasdtmf_detection_begin.Format:Upto80characters.



dtmf_digit_count [dword 0–31]: Max number of DTMF digits to receive. Setting 0 disables            

this.Default:0.



dtmf_terminate_digit [string]: The received DTMF digit that causes the driver to terminate           

DTMF digit collection being done by the modem by sending the dtmf_detection_end string.            

Leave blank to not use a terminate character. Format: 0 or 1 characters, typically # or *.                

Default:#.



dtr_toggle_msecs [dword 0–65535]: This is how long to keep the DTR line low during reset or               

closesothatamodemwillhangupthelineandreturnanOK.Default:200.



enable_init_flow_control [boolean]: This is for the rare modems that return OK following           

ATZ and have CTS low because they are unable to accept another command. This will probably               

neverbeusedsinceATZisnotsentforuserinitialization.Default:false.



hangup_timeout_msecs [dword 0–65535]: This is how long to wait for ATH0 command to            

complete.Default:2000.



line_type [string]: When dtmf_prompt is specified, the dtmf_detection_begin_string will be         

sent at the start of the call and received DTMF digits will be collected from the modem up until                  

either a dtmf_terminate_digit is received or a 6 second interdigit timeout occurs or a CNG tone               

isdetectedordtmf_digit_countnumberofdigitsarecollected.Default:NORMAL.



next_ring_response_timeout_msecs [dword 0–65535]: This is how many msecs to wait         

after a ring from the modem before resetting the internal ring counter. This will only apply for                

rings_before_answergreaterthan1andwhennotusingTAPI.Default:7500.



on_hook_msecs [dword 0–65535]: This is the minimum amount of time after the modem            

goes on hook from a prior connection before the driver will start a new connection (dial). This                

will allow the phone system to have time to disconnect the call upon noticing the modem on                

hook.Default:200.

ProprietaryFaxBack,Inc.2014 173

1 2 ... 168 169 170 171 172 173 174 175 176 177 178 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 173

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual