Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 179)

theapplicationsoonerwhenconnectionsfail.Default:60000.



get_send_post_phase_ok_timeout_msecs [dword 0–65535]: This is how long to wait for         

the OK after sending the +FET command. The modem will receive the post page response              

during this period. When the driver receives this OK it will send the +FDT signal and wait for a                  

CONNECTorfora+FHNG.



get_send_pre_phase_ok_timeout_msecs [dword 0–65535]: This is how long to wait for         

an OK while in the initial prephase of a fax send. When the driver receives an OK it will send a                    

+FDT.ThemodemusuallyreceivesCSIandDISinthistimeperiod.Default:35000.



hangup_timeout_msecs [dword 0–65535]: This is how long to wait for ATH0 command to            

complete.Default:2000.



line_type [string]: When dtmf_prompt is specified, the dtmf_detection_begin_string will be         

sent at the start of the call and received DTMF digits will be collected from the modem up until                  

either a dtmf_terminate_digit is received or a 6 second interdigit timeout occurs or a CNG tone               

isdetectedordtmf_digit_countnumberofdigitsarecollected.Default:NORMAL.



hangup_timeout_msecs [dword 0–65535]: This is how long to wait for ATH0 command to            

complete.Default:2000.



line_type [string]: When dtmf_prompt is specified, the dtmf_detection_begin_string will be         

sent at the start of the call and received DTMF digits will be collected from the modem up until                  

either a dtmf_terminate_digit is received or a 6 second interdigit timeout occurs or a CNG tone               

isdetectedordtmf_digit_countnumberofdigitsarecollected.Default:NORMAL.



next_ring_response_timeout_msecs [dword 0–65535]: This is how many msecs to wait         

after a ring from the modem before resetting the internal ring counter. This will only apply for                

rings_before_answergreaterthan1andwhennotusingTAPI.Default:7500.



on_hook_msecs [dword 0–65535]: This is the minimum amount of time after the modem            

goes on hook from a prior connection before the driver will start a new connection (dial). This                

will allow the phone system to have time to disconnect the call upon noticing the modem on                

hook.Default:200.



pause_before_send_command_msecs [dword 0–65535]: This specifies how long to pause        

when the protocol state is idle, answering, or dialing, before sending the "AT" command. There              

are some modems that upon sending an OK from a subsequent command, must have time to               

getreadytoreceivenewcharactersfromtheDTE.Default:100.



periodic_reset_timeout_msecs [dword 0–4294967295]: How often a reset sequence should        

be done to verify modem integrity. It is understood that some modems may periodically hang or               

go into a disabled power saver type of mode or that they may be turned off and on but the DSR                    

modem control change is not detected possibly because TAPI is being used. Therefore, the driver              

will reset the modem when it is idle for this amount of time. Setting this to 0 will disable this                   

periodicresetfeature.Default:600000.



receive_image_modulation_timeout_msecs [dword 065535]: How long to wait without       

receiving any image data before canceling the reception of image data. There is a USR modem               

that sometimes fails to send a DLE/ETX sequence at the end of image data. By having this                

timeout short enough, the driver will abort the image receive in a timeliness manner so as to                

receiveoneofthesubsequentendofpagecommands.Default:3000.



send_buffer_empty_flow_control [boolean]: If enabled and the send image buffer does not          

contain a complete scan line or ECM frame, this causes a particular byte (0 or current ECM flag                 

ProprietaryFaxBack,Inc.2014 179

1 2 ... 174 175 176 177 178 179 180 181 182 183 184 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 179

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual