Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 178)

errorsoccurring.Settingthistolowerthan19200hasthepossibilitythattheUART

wont be able to keep up with the modem modulation throughput due to extra DLE escaped               

characters.Default:38400.



dtmf_detection_begin [string]: When the line_type is DTMF_PROMPT, this command is sent          

to the modem before answering. It should cause the modem to go off hook, emit a prompt tone                 

if possible and collect and report received DTMF digits. This has the same format rules as the                

init_string, plus a / { sequence is translated to a DLE (0x10) character and a /} sequence is                 

translatedtoaETX(0x03)character.Format:Upto80characters.Default:#CLS=8A.



dtmf_detection_end [string]: This is what needs to be sent to the modem to get it out of the                 

state that the dtmf_detection_begin put it in. It is sent by the driver when either the 6 second                 

interdigit DTMF timeout occurs or the dtmf_terminate_digits is received. This has the same            

formatrulesasdtmf_detection_begin.Format:Upto80characters.



dtmf_digit_count [dword 0–31]: Max number of DTMF digits to receive. Setting 0 disables            

this.Default:0.



dtmf_terminate_digit [string]: The received DTMF digit that causes the driver to terminate           

DTMF digit collection being done by the modem by sending the dtmf_detection_end string.            

Leave blank to not use a terminate character. Format: 0 or 1 characters, typically # or *.                

Default:#.



dtr_toggle_msecs [dword 0–65535]: This is how long to keep the DTR line low during reset or               

closesothatamodemwillhangupthelineandreturnanOK.Default:200.



enable_init_flow_control [boolean]: This is for the rare modems that return OK following           

ATZ and have CTS low because they are unable to accept another command. This will probably               

neverbeusedsinceATZisnotsentforuserinit.Default:false.



get_receive_image_end_ok_timeout_msecs [dword 0–65535]: This is how long to wait        

for an OK after receiving the DLE/ETX sequence that terminates a receive image. The modem              

will receive the post page signal during this period. When the driver receives the OK, it will send                 

a +FDR and either start waiting for an image CONNECT if a MPS/EOP was received by the                

modem or start waiting for a prephase OK because an EOM was received by the modem.               

Default:30000.



get_receive_image_start_connect_timeout_msecs [dword 0–65535]: This is how long to       

wait for a CONNECT after sending +FDR. The modem will usually perform its training during this               

period. If it returns an OK during this time the driver will assume it has reported a new DCS and                   

is stepping down its training rate. The driver will reissue the FDR and restart this timeout. If a                 

modem steps through all training rates without returning new DCS/OK responses, this timeout            

would need to be quite large to achieve connection. Smaller values will return control to the               

applicationsoonerwhenconnectionsfail.Default:60000.



get_receive_pre_phase_ok_timeout_msecs [dword 0–65535]: This is how long to wait for         

an OK while in the initial prephase of a fax receive. When the driver receives an OK it will send                   

a +FDR. The modem usually exchanges TSI/CSI and DIS/DCS in this time period. Default:             

35000.



get_send_image_start_connection_timeout_msecs [dword 0–65535]: This is how long      

to wait for a CONNECT after sending +FDT to release the modem to send the TSI/DCS and                

perform training. If the modem returns an OK the driver will assume it has received an FTT and                 

is stepping down to a new baud rate. The driver will reissue the +FDT and restart this timeout.                 

If a modem steps through all training rates without returning new DCS/OK responses, this             

timeout would need to be quite large to achieve connection. Smaller values will return control to               

ProprietaryFaxBack,Inc.2014 178

1 2 ... 173 174 175 176 177 178 179 180 181 182 183 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 178

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual