Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 180)

byte) to be continually sent when the serial helper drivers buffers become empty. This will              

prevent the modem from dropping carrier when its buffers run dry. If this is disabled and you                

have a latent filling of the drivers send image buffer by ICANFax, there is the possibility that you                 

might experience a send underrun error because the modem drops carrier before all the page              

datahasbeensent.Default:true.



send_image_modulation_timeout_msecs [dword 0–4294967295]: This is how long to       

wait after sending a block of send image data to the modem before assuming the modem is                

having problems. This number should be large enough to account for the time done by the               

modemandserialdriverbuffering.Default:200000.



slow_at_pause_msecs [dword 0–65535]: This is how many msecs to pause in the middle            

and at the end of the "AT" for any command sent after a baud rate change. This gives the                  

modem time to auto baud and detect data/stop bit format before returning to its normal              

commandinterpretingstate.Usethisforoldmodems.Default:100.



speaker_mode [string]: State of device’s speaker. This translates to an ATM# command.           

Default:ON_UNTIL_CARRIER.



speaker_volume [string]: Volume of device’s speaker. This translates to an ATL# command.           

Default:LOW.



stolen_port_restore_timeout_msecs [dword 0–65535]: This was used in Win 16 and DOS,          

but probably does not have any application for when using TAPI in Win 32 since the Unimodem                

driver is in control or modem reinitializes when an app is done using a port. When not using                 

TAPIinWin32,thereisnowaythattheportcanbestoleninthefirstplace.Default:1000.



wait_connect_xon_msecs [dword 0–65535]: How long to wait for the XON following the           

CONNECT result code from the modem. If after this time period an XON is not received, the                

driverwillstartstreamingimagedatatothemodem.Default:1000.



allowed_receive_baud_rates [string]: This setting restricts a modem to use only certain          

baud rates. Use this to block a modem from using a rate or rates that it supports, but are                  

unreliable in your environment or are undesirable for some other reason. On transmitting, use             

this as a mask; the modem will use only those rates you list. On receiving, set the fastest and                  

slowestrates;themodemwillallowthoseandanyinbetween.

Format:Commaseparatedlistof14400,12000,9600,7200,4800and2400.

Default:14400,12000,9600,7200,4800,2400.



allowed_send_baud_rates [string]: This setting restricts a modem to use only certain baud           

rates. Use this to block a modem from using a rate or rates that it supports, but are unreliable                  

in your environment or are undesirable for some other reason. On transmitting, use this as a               

mask; the modem will use only those rates you list. On receiving, set the fastest and slowest                

rates;themodemwillallowthoseandanyinbetween.

Format:Commaseparatedlistof14400,12000,9600,7200,4800and2400.

Default:14400,12000,9600,7200,4800,2400.



carrier_wait [dword 0–255]: Seconds the driver to wait in the “dialing” or “answering” states             

foracarrierfromtheremotedevicebeforehangingup.Default:45.



dial_wait [dword 0–255]: Seconds the driver to wait in the "ringing" state before hanging up.              

Default:45.



flow_control [string]: Designates the type of flow control to use when sending data. If the              

setting is XON_XOFF the driver observes XOFF signals when sending. The driver uses no flow              

controlwhenreceiving.Format:EitherXON_XOFForRTS_LEVEL.Default:RTS_LEVEL.

ProprietaryFaxBack,Inc.2014 180

1 2 ... 175 176 177 178 179 180 181 182 183 184 185 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 180

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual