Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 174)



pause_before_send_command_msecs [dword 0–65535]: This specifies how long to pause        

when the protocol state is idle, answering, or dialing, before sending the "AT" command. There              

are some modems that upon sending an OK from a subsequent command, must have time to               

getreadytoreceivenewcharactersfromtheDTE.Default:100.



periodic_reset_timeout_msecs [dword 0–4294967295]: How often a reset sequence should        

be done to verify modem integrity. It is understood that some modems may periodically hang or               

go into a disabled power saver type of mode or that they may be turned off and on but the DSR                    

modem control change is not detected possibly because TAPI is being used. Therefore, the driver              

will reset the modem when it is idle for this amount of time. Setting this to 0 will disable this                   

periodicresetfeature.Default:600000.



receive_image_modulation_timeout_msecs [dword 065535]: How long to wait without       

receiving any image data before canceling the reception of image data. There is a USR modem               

that sometimes fails to send a DLE/ETX sequence at the end of image data. By having this                

timeout short enough, the driver will abort the image receive in a timeliness manner so as to                

receiveoneofthesubsequentendofpagecommands.Default:3000.



send_image_modulation_timeout_msecs [dword 0–4294967295]: This is how long to       

wait after sending a block of send image data to the modem before assuming the modem is                

having problems. This number should be large enough to account for the time done by the               

modemandserialdriverbuffering.Default:200000.



slow_at_pause_msecs [dword 0–65535]: This is how many msecs to pause in the middle            

and at the end of the "AT" for any command sent after a baud rate change. This gives the                  

modem time to auto baud and detect data/stop bit format before returning to its normal              

commandinterpretingstate.Usethisforoldmodems.Default:100.



speaker_mode [string]: State of device’s speaker. This translates to an ATM# command.           

Default:ON_UNTIL_CARRIER.



speaker_volume [string]: Volume of device’s speaker. This translates to an ATL# command.           

Default:LOW.



stolen_port_restore_timeout_msecs [dword 0–65535]: This was used in Win 16 and DOS,          

but probably does not have any application for when using TAPI in Win 32 since the Unimodem                

driver is in control or modem reinitializes when an app is done using a port. When not using                 

TAPIinWin32,thereisnowaythattheportcanbestoleninthefirstplace.Default:1000.



allowed_receive_baud_rates [string]: This setting restricts a modem to use only certain          

baud rates. Use this to block a modem from using a rate or rates that it supports, but are                  

unreliable in your environment or are undesirable for some other reason. On transmitting, use             

this as a mask; the modem will use only those rates you list. On receiving, set the fastest and                  

slowest rates; the modem will allow those and any in between. Format: Comma separated list              

of14400,12000,9600,7200,4800and2400.

Default:14400,12000,9600,7200,4800,2400.



allowed_send_baud_rates [string]: This setting restricts a modem to use only certain baud           

rates. Use this to block a modem from using a rate or rates that it supports, but are unreliable                  

in your environment or are undesirable for some other reason. On transmitting, use this as a               

mask; the modem will use only those rates you list. On receiving, set the fastest and slowest                

rates; the modem will allow those and any in between. Format: Comma separated list of              

14400, 12000, 9600, 7200, 4800 and 2400. Default: 14400, 12000, 9600, 7200, 4800, and             

2400.



carrier_wait [dword 0–255]: Seconds the driver to wait in the “dialing” or “answering” states             

foracarrierfromtheremotedevicebeforehangingup.Default:45.



dial_wait [dword 0–255]: Seconds the driver to wait in the "ringing" state before hanging up.              

Default:45.



flow_control [string]: Designates the type of flow control to use when sending data. If the              

setting is XON_XOFF the driver observes XOFF signals when sending. The driver uses no flow              

controlwhenreceiving.Format:EitherXON_XOFForRTS_LEVEL.Default:RTS_LEVEL.



rings_before_answer[dword0–255]:Numberofringsbeforemodemacceptscall.

Default:1.

ProprietaryFaxBack,Inc.2014 174

1 2 ... 169 170 171 172 173 174 175 176 177 178 179 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 174

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual