Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario descargar pdf (Pagina 181)



rings_before_answer [dword 0–255]: Number of rings before modem accepts call. Default:          

1.



ser_device_name [string]: Win32 name for the serial port in the format of COMXXX where             

XXX can be 001–999. This does not need to be specified if the tapi_modem_name is specified.               

Format: Up to 6 characters. init_string [string]: This is the basic modem initialization string. It              

shouldresetthemodemandinittherequiredflowcontrol.Format:Upto80characters.

Default:&F&C1&D2V1E0S0=0S7=90^^.



AllmodemcommandsstartwithAT,sothisstringdoesnotneedAT.Thesymbols

inthestringmeanthefollowing:



^

2secondpause

\

Carriage return. There is a wait of init_string_timeout_msecs after carriage return to wait an             

OKtobereturned.

\\

Specifiesasingle\

^^\

Thisisinterpretedas\^^



init_string_timeout_msecs [dword 0–65535]: How long to wait for response after CR in           

theinit_stringifthereareno2secondpausesbeforeoraftertheCR.Default:5000.



io_buffer_size [dword 0–65535]: This is the size of the image buffer. The necessary buffer             

size depends on host CPU speed and load as well as connect speed. This buffer directly adds                

to driver page locked memory use so should be as small as possible. However, too small a                

bufferwillcausefaxestofail.Default:20480.



show_console_scroll_back_buffer_size [dword 0–4294967295]: When the debug output      

isCONSOLE,thisishowbigofabuffertobeusedforscrollback.Default:282144.



show_ring0_buffer_size [dword 0–4294967295 ]: How big of buffer for the page locked           

debug buffer that ring0 code writes to and ring3 code extracts from (on a thread) to the                

debugging output. This should be larger for when using serial capture mode since so much              

more data is written for debug. It should probably be only about 1K for when using T.30                

debug since the frequency and amount of T.30 debug is small enough that the ring3 code               

caneasilykeepupwritingtotheshowoutput.Default:65536.



debug_show_file_path [string(256)]: Partial path or complete path and file name of where           

to create debug file. If the debug_show_output is set for CONSOLE and the            

debug_show_file_path is specified in the registry, then you can get both CONSOLE and FILE             

debug output simultaneously. This is a device specific setting, but you can set the default              

foralldevicesbyspecifyingthisundertheglobalicanfaxsection.



csid[string(20)]:TheCSIforreceiveandtheTSIforsend.



allowed_receive_image_types [string]: These settings control the image types that the         

device can send and receive via the T.30 protocol over the telephone network. To receive or               

send some image types, the corresponding allowed_receive/send_transfer_type setting must        

includeECM.Format:Commaseparatedlistofthefollowing.Default:1D,2D,T6,JBIG.



1D

ProprietaryFaxBack,Inc.2014 181

1 2 ... 176 177 178 179 180 181 182 183 184 185 186 ... 202 203

Comentarios a estos manuales

Sin comentarios

Faxback NET SatisFAXtion 9.0 - Fax Server Manual Manual de usuario Pagina 181

Comentarios a estos manuales

Relacionado con productos y manuales para Software Faxback NET SatisFAXtion 9.0 - Fax Server Manual